| Soap Molds - Soap Molds - Soap
Molds - Soap Molds |
| |
|
8 Pound Wooden Soap Mold &
Cutters for cold process |
|
 |
Our Custom Wooden Soap Mold - holds 8
pound cold process soap recipe.
Inside dimensions: 10.50" x 8.75"
$20.00
Instructions on how to line are at the
bottom of this page - just scroll down to them.
Ask for the recipe when you order your mold
Click here for shopping cart
|
|
 |
Our Wooden/wire soap cutter set - designed for
the soap mold above
Cuts the 8 pound soap block into 3 strips (logs). The bar cutter cuts the
strips into soap bars.
Set $22.00 - Individual bar cutter or strip cutter $11.00
Instructions on use at the bottom of this page. |
| More information
on these molds and cutters are at the bottom of this page. |
|
|
|
We have four plastic soap mold lines in stock with over
300 molds to choose from
Manufactured especially for Melt & Pour Soap
Base - can also be used for cold process soap. Some are also designed for
bath bombs. |
|
 |
3-D Soap Molds
These designer soap molds
manufactured by 3-D Soap Molds are used to create professional
Melt & Pour glycerin soaps, and Cold Process hand-made soaps. These
heavy duty soap molds
are manufactured from heavy duty ABS plastic, and High Impact Polystyrene
plastic which are both food safe and FDA approved. Our sturdiest molds.
3-D Mold Shopping Cart |
| |
|
|
 |
Milky Way Soap
Molds
Milky Way bar molds
come on sheets of clear, flexible PVC plastic 9" x 9" square. We also are
carrying a few of their tray molds. Artistic, unusual and lots of variety
are the hallmarks of the Milky Way Molds. Designed by Catherine Failor.
$6.00 each
Milky Way Shopping Cart |
| |
|
  |
Flexus Molds
Flexible soap molds greatly
improve the release of your cured soap from the mold cavity. This insures
that more detail and smaller detail, which may have crumbled before, is now
not only possible, but easy.
By using flexible vinyl instead of hard plastic, Flexus Molds are more
durable and not prone to the cracking and warping that other molds have
Flexus Shopping Cart |
|
|
|
|
 |
Precision Soap Line
These clear plastic molds are very sturdy, heavy duty. Molds are
3 and 4 cavity. $6.00 ea
They are on close out - See what's left - click on shopping cart below.
Shopping Cart
|
| |
| Instructions on how to line cold
process soap mold |
|
 |
To line your mold like the picture on the
left we used plastic wrap and a cut up trash bag. First we put the
plastic wrap on the short sides of the mold. Then we cut a rectangular
piece of trash bag 10.50" x about 20" and placed it down the middle and over
both sides. We used a small amount of scotch tape to hold it in place.
We made a lid by cutting a piece of cardboard
to fit over the mold and then wrapped it in plastic wrap and taped it.
You could also get a cheap plastic cutting board that is close to the mold
dimensions-should be larger, not smaller. |
|
Soap Cutter Instructions
The
cutters work best when the soap is not too hard - cut between 24 to 36 hours
from the time you put in mold. I'm assuming you are using my recipe. If you
use a recipe that makes a softer bar of soap, you can wait longer. If you wait
too long, it won't work at all. The wire can't cut it.
To cut
the strips: Take soap out of mold and set on end with the 8-3/4 end on the
working surface. Take your strip cutter (that's the shorter one with the wire
at 3-1/2 inches) and turn it upside down. Pass it through the end and across
the soap to make a strip of soap 8-3/4 inches long and 3-1/2 inches wide. Pass
it through the block again and you will have 3 equal strips ready to be cut into
bars.
To cut
bars: The bar cutter is set at 1 inch. Just set the cutter on the table with
the U up. Take your strip and set it on the cutter and pass it through the
wire. Keep doing this until the entire strip is cut into 9 bars. Each bar
weighs approximately 4 to 4-1/4 ounces. There are two additional holes made one
at 7/8 inch and one at 15/16 inch.
|
